DIY Homemade Electronic Coyote Predator Caller

Do-It-Yourself Homemade Electronic Coyote Predator Caller
Do-It-Yourself Homemade Electronic Coyote/Predator Caller

Being the Do-It-Yourself guy I am, I thought a homemade coyote caller would be a lot cheaper than a commercial electronic call and a fun project for me to tinker around with.

I started out using an old Browning flashlight housing. I got an inexpensive mp3 player and the Speco SPC-5P speaker from eBay and a old double male audio cable I had kicking around the house. The rest of the parts needed I ordered from Radio Shack.

The battery pack holds eight batteries so to achieve 9 volts (6 times 1.5v AA batteries equals 9v) I placed a piece of copper tubing across one of the two AA battery slots. Having this larger pack of batteries lasts a lot longer than just a single 9v battery.

I then cut the bottom of the mini amplifier off so that it would fit inside the flashlight case and wired it as shown in the diagram.

Homemade Electronic Coyote Call Wiring Diagram Using audio editing software I changed the meta tags of all my predator MP3 sounds. I changed the "artist" tag to different animal sounds. In this way I could browse by artist and bring up all the rabbit or coyote sounds etc. I set the MP3 player to repeat so I can pause and play the same sound over and over.

Another thing I like to do with my MP3 files is make 20-30 minute calling scenario MP3 files. I do this by bringing various sounds into my audio editing software. For instance I will have two minutes of silence at the beginning, then I will have a series of mouse squeaks and then a minute or so pause. Then some louder rabbit squalls and then a couple of series of the rabbit squalls over a ten minute window. Towards the end I will often throw in a coyote challenge bark/howl and then a distress ki-yi bark. You can also mix in bird sounds all along the way like a crow or a magpie. I think you get the idea. You can have fun and make all sorts of various predator calling sequences.

 

Two coyotes, Model 1885, 243 WSSM, Homemade Electronic Coyote Caller
A pair of coyotes taken with my homemade electronic caller. You can read more about this hunt in my 243 WSSM Model 1885 Coyote Double journal entry.

When I have these long pre-made audio sequences I can set my call out in front of me however far I want. I now have two minutes to get back into position before the mouse squeaking starts. Then I sit back and enjoy the show.

Basic parts list that I used:

  • MP3 Player
  • Housing, from a flashlight case or gym bag etc.
  • Speco SPC-5P Speaker
  • 8 "AA" Battery Holder (Radio Shack, Catalog #270-407)
  • Red LED with Holder (Radio Shack, Catalog #276-084), Optional but nice to know when it is on.
  • Fully Insulated 9V Battery Snap Connectors (Radio Shack, Catalog #270-325)
  • SPST 3-Amp "Soft-Feel" Push On-Push Off Switch (Radio Shack, Catalog #275-1565)
  • 3.5mm male to male audio extension cable

 

Mini Amplifier used for Do-It-Yourself Homemade Electronic Coyote Predator Caller Mini Amplifier with bottom cut off used for Do-It-Yourself Homemade Electronic Coyote Predator Caller
 Mini Amp before I cut the bottom off.  Mini Amp with bottom battery compartment removed.
   
Do-It-Yourself Homemade Electronic Coyote Predator Caller Inside Do-It-Yourself Homemade Electronic Coyote Predator Caller
Battery pack, Mini Amp, and Speaker. View inside the main compartment compartment.
   
Speaker with two screws holding it on Electronic Coyote Predator Caller Do-It-Yourself Homemade Electronic Coyote Predator Caller
I drilled two holes through the speaker and used screws to hold the speaker in place. View of the outside before wrapping it in a removable camouflage wrap.

 

Additional information